K1-60
K1-60 is a cationic, rapid-setting bitumen emulsion with a minimum binder content of 60%. It breaks quickly on contact with aggregate, so roads can reopen fast. No heating is needed on site, which cuts fuel costs and emissions.
Where K1-60 is used
Bitumen emulsion is fine droplets of bitumen dispersed in water with an emulsifier. It is applied cold, then "breaks" as the water separates, leaving a bitumen film. Cationic emulsions carry a positive charge and suit most aggregates. Anionic emulsions carry a negative charge.
- 01Tack coats and surface dressing
- 02Cold application with no heating equipment on site
- 03Works with both siliceous and limestone aggregates
- 04Road maintenance programmes and remote projects
Conforms to EN 13808
Supplied to EN 13808. Tested for viscosity, binder content, settlement or storage stability, sieve residue and properties of the recovered binder.
Typical specifications — K1-60
| Property | Unit | Min | Max | Test method |
|---|---|---|---|---|
| Efflux time (2 mm, 40°C) | s | 15 | 70 | EN 12846-1 |
| Breaking value | – | 70 | 155 | EN 13075-1 |
| Binder content | % wt | 60 | – | EN 1428 |
| Sieve test | % wt | – | 0.10 | EN 1429 |
| Storage stability (24 h) | % | – | 1 | EN 12847 |
| Tests on residue | ||||
| Penetration at 25°C | 0.1 mm | 100 | 250 | ASTM D5 |
| Ductility at 25°C | cm | 40 | – | ASTM D113 |
| Solubility in trichloroethylene | % | 97.5 | – | ASTM D2042 |
Typical values based on EN 13808. The binding specification for each cargo is the certificate of analysis issued at loading. Custom specifications are available on request.
Storing K1-60
Temperature: Store between about 10°C and 85°C. Never let emulsion freeze, because freezing breaks it irreversibly. Never heat it above 85°C.
Tanks: Use clean vertical tanks with gentle circulation or periodic stirring. Never mix cationic and anionic emulsions, because they break on contact.
Handling: Pump with low-shear pumps and avoid air entrainment. Excessive shear or agitation can cause premature breaking.
Shelf life: Use within the period stated on the data sheet, typically weeks to a few months. Stir or circulate before use if it has been standing.
How we ship K1-60
Get a price for K1-60
Tell us the quantity and destination port. We'll send you a written offer today.
- No cost to ask
- FOB · CIF · CFR · DAP
- LC, SBLC or TT against documents
K1-60: common questions
What is K1-60?+
K1-60 is a cationic, rapid-setting bitumen emulsion with a minimum binder content of 60%. It breaks quickly on contact with aggregate, so roads can reopen fast. No heating is needed on site, which cuts fuel costs and emissions.
What is K1-60 used for?+
K1-60 is mainly used for: tack coats and surface dressing; cold application with no heating equipment on site; works with both siliceous and limestone aggregates; road maintenance programmes and remote projects.
Which standard does WGV's K1-60 meet?+
Supplied to EN 13808. Tested for viscosity, binder content, settlement or storage stability, sieve residue and properties of the recovered binder.
How is K1-60 shipped?+
WGV Oil Trading ships K1-60 by steel drums, ibc totes, flexitanks or bulk, on FOB, CIF, CFR or DAP terms. Every cargo is inspected at the load port by SGS, Intertek or an equivalent independent inspector.
How do I get a price for K1-60?+
Send the quantity, destination port, preferred Incoterms and timing through the quote form on this page, by WhatsApp on +34 663 192 105, or by email to sales@wgvoiltrading.com. WGV Oil Trading replies with a written offer the same day. Payment is by documentary LC, SBLC or TT against documents.